# SER10 MAX BIOS设置 # 调整CPU功率教程 #### **1.首先关闭主机，按下电源启动后，当屏幕上出现logo，迅速按下键盘上的Del键进入BIOS** #### [![image.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/gqIimage.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/gqIimage.png) #### **2.选择菜单栏第二项【Advanced】，再选择子选项【OEM Features Management】进入设置** [![Screenshot_2026-05-12_10-07-29.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/6ivaGv9IgQLCGB7h-screenshot-2026-05-12-10-07-29.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/6ivaGv9IgQLCGB7h-screenshot-2026-05-12-10-07-29.png) #### **3.选择【PowerLimit Setting】使用回车键进入调整功率选项** **Balance Mode为54W，Performance mode为65W，选择需要调整的功率，按Enter确认** [![Screenshot_2026-05-12_10-07-34.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/1cXjC56GZMW4FmZ5-screenshot-2026-05-12-10-07-34.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/1cXjC56GZMW4FmZ5-screenshot-2026-05-12-10-07-34.png) #### **5.调整完成后，再按【F4】保存设置并退出重启，设置完成** [![Screenshot_2026-05-12_10-07-38.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/rGH1QGtEwMh1XsSV-screenshot-2026-05-12-10-07-38.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/rGH1QGtEwMh1XsSV-screenshot-2026-05-12-10-07-38.png) # 关机USB断电设置 #### 零刻SER10MAX 关机后，USB还是有供电的，如果你想要关机取消USB供电，接下来教大家设置，关机后关闭USB供电 ``` 此教程只能关闭UBS供电，Typec接口暂时无法进行关闭。 ``` #### **操作步骤：** #### **1. 首先关闭主机，按下电源启动后，当屏幕上出现logo后，迅速按下键盘上的Del键进入BIOS** #### [![image.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/bxximage.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/bxximage.png) #### **2. 进入BIOS后，使用方向键切换到【**Advanced**】，进入【OEM Features Management】** [![Screenshot_2026-05-12_10-07-29.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/0GZ2iM9O8QB9Ew8k-screenshot-2026-05-12-10-07-29.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/0GZ2iM9O8QB9Ew8k-screenshot-2026-05-12-10-07-29.png) #### **3. 在【Usb Power Controller】选项，【On】：默认为开启状态，关机后USB通电。【OFF】：关机后USB断电状态，可以根据自己的需求进行设置** [![Screenshot_2026-05-12_10-07-47.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/2xGSOQRSwaxMqEvt-screenshot-2026-05-12-10-07-47.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/2xGSOQRSwaxMqEvt-screenshot-2026-05-12-10-07-47.png) #### **4. 修改完成后，按【F4】，选择【Y】进行保存退出即可** [![Screenshot_2026-05-12_10-07-51.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/fmH8jUMqQWmmYCKX-screenshot-2026-05-12-10-07-51.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/fmH8jUMqQWmmYCKX-screenshot-2026-05-12-10-07-51.png) #### **注意事项：**关闭关机UBS断电后 休眠唤醒相关的功可能能会失效哦！ # 调整显存大小 **调整显存大小可以对计算机的图形处理和游戏表现产生影响。** **请注意，如果您将显存调整为过大的值，可能会降低系统的稳定性，或者在使用大量显存时出现帧率下降的情况。因此，在调整显存大小之前，请确保了解您的计算性能和限制。** ### **操作步骤：** #### **1. 首先关闭主机，按下电源启动后，当屏幕上出现logo后，迅速按下键盘上的Del键进入BIOS** [![image.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/1AGimage.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/1AGimage.png) #### **2. 进入BIOS后，使用方向键切换到【Advanced】，进入【AMD CBS】选项** [![Screenshot_2026-05-12_10-09-45.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/r3QwFf1ANXZflIVS-screenshot-2026-05-12-10-09-45.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/r3QwFf1ANXZflIVS-screenshot-2026-05-12-10-09-45.png) #### **3. 进入【NBIO Common Options】选项** [![Screenshot_2026-05-12_10-12-12.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/FkAXbwEpw3DykkkB-screenshot-2026-05-12-10-12-12.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/FkAXbwEpw3DykkkB-screenshot-2026-05-12-10-12-12.png) #### **4. 进入【GFX Configuration】选项** [![Screenshot_2026-05-12_10-12-15.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/D3103mwVZo7yxFcZ-screenshot-2026-05-12-10-12-15.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/D3103mwVZo7yxFcZ-screenshot-2026-05-12-10-12-15.png) #### **5. 在【Dedicated Graphics Memory】这里可以调整显存的大小，可以根据自己的需求进行修改** [![Screenshot_2026-05-12_10-12-42.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/GPbbA0um9v5DYL8C-screenshot-2026-05-12-10-12-42.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/GPbbA0um9v5DYL8C-screenshot-2026-05-12-10-12-42.png) #### **6. 调整完成后，再按【F4】保存设置并退出重启，设置完成** [![Screenshot_2026-05-12_10-12-47.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/awDEFO6gMKoMoQuQ-screenshot-2026-05-12-10-12-47.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/awDEFO6gMKoMoQuQ-screenshot-2026-05-12-10-12-47.png) # 来电自启设置 #### 操作步骤： 1️⃣ 首先关闭主机，按下电源启动后，当屏幕上出现 logo 后，迅速按下键盘上的 Del 键进入 BIOS[![图片 1.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-09/scaled-1680-/qqvzn5yTZld20HoY-1.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-09/qqvzn5yTZld20HoY-1.png) 2️⃣ 进入 BIOS 后，使用方向键切换到【Advanced】，进入【AMD CBS】 [![Screenshot_2026-05-12_10-14-44.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/zTpa1ZGScjZgiOVc-screenshot-2026-05-12-10-14-44.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/zTpa1ZGScjZgiOVc-screenshot-2026-05-12-10-14-44.png) 3️⃣ 进入【FCH Common Options】选项 [![Screenshot_2026-05-12_10-14-48.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/YjZuCtSUYXWyeui9-screenshot-2026-05-12-10-14-48.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/YjZuCtSUYXWyeui9-screenshot-2026-05-12-10-14-48.png) 4️⃣ 进入【Ac Power Loss Options】选项 [![Screenshot_2026-05-12_10-14-49.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/rMZEyIvFUdXR3qoe-screenshot-2026-05-12-10-14-49.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/rMZEyIvFUdXR3qoe-screenshot-2026-05-12-10-14-49.png) 5️⃣ 开启来电自启就选择【Always on】，关闭就选择【Always off】 [![Screenshot_2026-05-12_10-14-53.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/FNnvHjmzAnfkzcK2-screenshot-2026-05-12-10-14-53.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/FNnvHjmzAnfkzcK2-screenshot-2026-05-12-10-14-53.png) 6️⃣ 设置完成后，按【F4】，选择【Yes】确认保存退出 [![Screenshot_2026-05-12_10-14-55.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/IiG2sJHgeKtZcckQ-screenshot-2026-05-12-10-14-55.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/IiG2sJHgeKtZcckQ-screenshot-2026-05-12-10-14-55.png) # 调整风扇转速 *操作步骤：* 1\. 首先关闭主机，按下电源启动后，当屏幕上出现 logo 时，迅速按下键盘上的 `Del` 键进入 BIOS。[![图片 1.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-09/scaled-1680-/4TdbmJEsxCvaisbl-1.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-09/4TdbmJEsxCvaisbl-1.png) 2\. 进入 BIOS 后，使用方向键切换至【Advanced】选项，进入【Hardware Monitor】菜单。 [![Screenshot_2026-05-12_10-16-58.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/VQOM4U9hcZ9PTJZu-screenshot-2026-05-12-10-16-58.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/VQOM4U9hcZ9PTJZu-screenshot-2026-05-12-10-16-58.png) 3\. 继续进入【Smart Fan Function】菜单。 [![Screenshot_2026-05-12_10-17-07.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/uOGgh7k89KHeswCZ-screenshot-2026-05-12-10-17-07.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/uOGgh7k89KHeswCZ-screenshot-2026-05-12-10-17-07.png) 4\. 继续进入【Cpu Fan Setting】菜单 [![Screenshot_2026-05-12_10-17-10.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/SLAODpvU2w4zNZHV-screenshot-2026-05-12-10-17-10.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/SLAODpvU2w4zNZHV-screenshot-2026-05-12-10-17-10.png) 5\. 【Cpu Fan Mode】为 CPU 风扇设置，共有三个模式可选： [![Screenshot_2026-05-12_10-17-33.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/oS6ZR01F8Y1NiJFr-screenshot-2026-05-12-10-17-33.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/oS6ZR01F8Y1NiJFr-screenshot-2026-05-12-10-17-33.png) **【Manual Mode】** 该模式下为预设参数，但您可以手动设置风扇 PWM 参数的值，范围在 0 到 255 之间。数值越高，风扇转速越快。 [![Screenshot_2026-05-12_10-17-49.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/gAZBJ43dN7TTgs7X-screenshot-2026-05-12-10-17-49.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/gAZBJ43dN7TTgs7X-screenshot-2026-05-12-10-17-49.png) > ⚠️ **请注意**：我们强烈建议您将数值设置为 65 以上，以避免 CPU 过热。 **【Full on Mode】** 该模式为全速模式，风扇将以最高转速运行。 [![Screenshot_2026-05-12_10-18-21.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/AG0eweIqYk3OD7D8-screenshot-2026-05-12-10-18-21.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/AG0eweIqYk3OD7D8-screenshot-2026-05-12-10-18-21.png) **【Automatic Mode】** 该模式为自定义模式，可以对温度及转速进行自定义设置，如果您需要设置更多参数，可使用该模式。 [![Screenshot_2026-05-12_10-17-12.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/Od2F83V5qGza3P0e-screenshot-2026-05-12-10-17-12.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/Od2F83V5qGza3P0e-screenshot-2026-05-12-10-17-12.png) 当【Cpu Fan Mode】设置为【Automatic Mode】时，具体参数解释如下： **SMF Temperature Limit of OFF：30** 风扇停止工作温度。默认参数是 30 度，当 CPU 温度低于 30 度时风扇停止转动。 **SMF Temperature Limit of OFF：35** 风扇启动工作温度。默认参数是 35 度，CPU 温度高于 35 度时风扇开始转动。 **SMF start PWM：80** PWM 数值为 CPU 风扇转动的速度，满速为 127 (100%)，默认数值为 80 (50%)。当超过风扇全速工作温度时，风扇将不受 PWM 数值影响，以全速工作。 **Full PWM Temperature：91** 风扇全速工作温度。当 CPU 温度高于 91 度后，风扇以最大转速工作。 **SMF SLOPE PWM：1 PWM** 风扇转速上升的系数。当温度每上升一度，风扇就以 `SMF Start PWM` 值为基数提高系数倍的转速。 以上参数可以根据自己的需求进行修改。 6\. 调整完成后，按下【F4】，选择【Yes】保存并退出即可生效。 [![Screenshot_2026-05-12_10-19-00.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/scaled-1680-/Lb8kbkozhv9VDE7G-screenshot-2026-05-12-10-19-00.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-05/Lb8kbkozhv9VDE7G-screenshot-2026-05-12-10-19-00.png) --- ⚠️ **重要提示** 调整 CPU 转速可能会对主机造散热影响，因此请谨慎操作。如果您不确定如何更改设置，请寻求专业人员的帮助。 # SER10MAX 网络唤醒教程 ##### SER10MAX 支持网络唤醒，BIOS 已默认开启，无需手动设置，只需在系统中开启即可。 ### 操作步骤 1. ##### 在系统内按下 `Win + X` ，打开**设备管理器** [![1.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/cQ2IkQaOSqmKaGjX-1.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/cQ2IkQaOSqmKaGjX-1.png) 2. ##### 展开**网络适配器** 3. ##### 双击打开 **`Marvell AQtion 10Gbit Network Adapter` **驱动 [![2.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/bzO9DENxBFW3mtQx-2.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/bzO9DENxBFW3mtQx-2.png) 4. ##### 点击弹出窗口顶部的**高级**选项卡 5. ##### 启用以下两个功能选项
属性名称值说明
`Wake from power off state`（关机状态下唤醒）`Enable`**关键**：关机（含断电式休眠）后能否被唤醒
`Wake on Magic Packet`（幻数据包唤醒）`Enable`**关键**：通过 Magic Packet 协议唤醒
6. ##### 设置好以后点**确定**即可 [![3.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/yG2lfvcqnWXMZJpZ-3.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/yG2lfvcqnWXMZJpZ-3.png) [![4.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/A5dH2hwlpCzdxoiN-4.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/A5dH2hwlpCzdxoiN-4.png) ##### 到这里就已经设置好网络唤醒了，可以通过局域网内的其他设备或路由器对主机进行远程唤醒操作了！ --- ### 验证方法 ##### 通过支持网络唤醒的路由器选择对应的设备或者是输入设备的IP进行唤醒 [![image 7.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/FScimage-7.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/FScimage-7.png) ##### 通过局域网内其他电脑进行唤醒 [![image 8.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/xSgimage-8.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/xSgimage-8.png) ##### 软件分享：[https://lanzoux.com/i3boW0z9eh4f](https://lanzoux.com/i3boW0z9eh4f)
---
### 常见问题 #### Q1：设置了但还是无法网络唤醒？ ##### 按以下顺序排查： 1. ##### **路由器开了节能 / WOL 过滤** → 多数家用路由器默认不会过滤 Magic Packet，但如果开了"AP 隔离"或"无线节能"需关掉 2. ##### **发送端和接收端不在同一局域网** → WOL Magic Packet **不能跨路由器**（除非路由器支持 WOL 中继） 3. ##### 禁用系统内的快速启动，[点我跳转教程](https://doc.bee-link.com.cn/books/windows/page/windows-11) #### Q3：唤醒后能不能远程控制？ ##### WOL 只负责开机，可以搭配远程控制软件使用。 #### Q4：开着 WOL 会不会很耗电？ ##### 不会。关机状态下网卡保持监听网络数据包的极低功耗，功耗低到几乎可以无视。 # SER10MAX RTC 定时开机设置教程 ### 操作步骤： 1. ##### 先将主机正常关机，按下电源键后立即连续短按 **Del** 键，进入 BIOS。![image.png](https://doc.bee-link.com.cn/uploads/images/gallery/2025-03/scaled-1680-/gqIimage.png) 2. ##### 进入 BIOS 后，检查首页 【**System Date**】和【**System Time**】显示的时间与您当地时间一致。 如时间不一致可以用方向键移动到选项上，手动输入正确时间，然后按下回车确认。 [![Screenshot_2026-06-26_16-14-46.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/Iz91oncQNwkfJfWJ-screenshot-2026-06-26-16-14-46.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/Iz91oncQNwkfJfWJ-screenshot-2026-06-26-16-14-46.png) 3. ##### 接下来使用方向键切换到【**Advanced**】，再进入子选项【**OEM Features Management**】。 [![Screenshot_2026-06-26_16-14-48.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/d936VKot88AgGQ5K-screenshot-2026-06-26-16-14-48.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/d936VKot88AgGQ5K-screenshot-2026-06-26-16-14-48.png) 4. ##### 选择【**Wake On RTC**】，有三个选项，默认为【**Disable（禁用）**】。 [![Screenshot_2026-06-26_16-14-55.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/vMxwND0YpQVTHT6K-screenshot-2026-06-26-16-14-55.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/vMxwND0YpQVTHT6K-screenshot-2026-06-26-16-14-55.png) 5. ##### 选择需要使用的模式，下面是模式的说明： 【**Fixed Time**】，固定时间定时开机： `Wake up day` ：可设置 **0-31** 的时间范围，0 为每日，1-31 为具体某一日； `Wake up hour` ：可设置 **0-23** 的时间范围，表示 0-23 时； `Wake up minute` ：可设置 **0-59** 的时间范围，表示 0-59 分； `Wake up second` ：可设置 **0-59** 的时间范围，表示 0-59 秒。 例如 **\[0 16 20 0\]**，表示每天下午 16 点 20 分自动开机。 [![Screenshot_2026-06-26_16-15-04.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/boLEdm81y3YQLsbt-screenshot-2026-06-26-16-15-04.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/boLEdm81y3YQLsbt-screenshot-2026-06-26-16-15-04.png) ##### 【**Dynamic Time**】，延时自动开机： `Wake up minute increase` ：可设置 **1-5** 的时间范围，表示将会在关机后数分钟自动开机。 例如设置为 3，则将会在关机后 3 分钟自动开机。 [![Screenshot_2026-06-26_16-15-09.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/amGQjcEBxIQVROnp-screenshot-2026-06-26-16-15-09.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/amGQjcEBxIQVROnp-screenshot-2026-06-26-16-15-09.png) 6. ##### 设置好以后，按 【**F4**】 保存重启即可生效。 [![Screenshot_2026-06-26_16-15-05.png](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/scaled-1680-/sxLy2qPsrGE4VwpV-screenshot-2026-06-26-16-15-05.png)](https://doc.bee-link.com.cn/uploads/images/gallery/2026-06/sxLy2qPsrGE4VwpV-screenshot-2026-06-26-16-15-05.png)